Clearance Sale
Injection molding machines at special prices - new, demo, and used
Configuration
DH480/i3200
DH
·S/N: H04800002
DHⅡ480/i3200 two-platen machine with Inovance servo drive and KEBA 2980-0120 controller. Standard factory build, GB standard.
Show full specificationsHide specifications
Configuration
DHⅡ480/i3200 + Servo (Inovance) + GB standard + KEBA 2980-0120 controller. Standard type.
Clamping unit
- Clamping force
- 4800 kN
- Clamping stroke
- 750 mm
- Tie bar spacing
- 860×860
- Max mold height
- 900 mm
- Min mold height
- 300 mm
- Ejector stroke
- 260 mm
- Ejector force
- 182 kN
- Ejector pins
- 11
- Platen dimensions
- 1275×1275
Injection unit
- Screw code
- A
- Screw diameter
- 70 mm
- L/D ratio
- 23.6
- Shot size
- 1516 cm³
- Injection weight (PS)
- 1380 g
- Injection pressure
- 212.1 MPa
- Screw speed
- 250 rpm
- Injection stroke
- 394 mm
Other
- Max pump pressure
- 20 MPa
- Heater power
- 37.1 kW
- Hopper capacity
- 50 kg
- Oil capacity
- 580 L
- Total weight
- 18 t
- Machine dimensions
- 7.2×2.2×2.3 m
- Dry cycle time
- 4.3 s
DH550/i4800
DH
·S/N: H1055-0003
DH550/i4800 with dual-cylinder dual-rod injection and pneumatic sequence-valve signalling. Originally a Shanghai Yazhan unit converted to our factory specification.
Show full specificationsHide specifications
Configuration
DH550/i4800. Dual-cylinder, dual-rod injection unit; outputs signal to mold pneumatic sequence valve during injection. Reserved centralised water supply for moving & fixed mold channels — each with one set of 3/4" pipe fittings. Shanghai Yazhan machine converted to our factory specification.
Clamping unit
- Clamping force
- 5500 kN
- Clamping stroke
- 1700 mm
- Tie bar spacing
- 915×915
- Max mold height
- 1000 mm
- Min mold height
- 400 mm
- Ejector stroke
- 260 mm
- Ejector force
- 182 kN
- Ejector pins
- 21
- Platen dimensions
- 1335×1335
Injection unit
- Screw code
- A
- Screw diameter
- 80 mm
- L/D ratio
- 23.4
- Shot size
- 2242 cm³
- Injection weight (PS)
- 2042 g
- Injection pressure
- 220.4 MPa
- Injection rate
- 805 g/s
- Screw speed
- 150 rpm
- Max injection speed
- 160 mm/s
- Injection stroke
- 446 mm
Other
- Max pump pressure
- 23.5 MPa
- Pump motor power
- 107 kW
- Heater power
- 48 kW
- Hopper capacity
- 100 kg
DH550/i3800
DH
·S/N: H1055-0011
DH550/i3800 two-platen frame ready for buyer-specified plasticising assembly. Screw and barrel not installed at factory.
Show full specificationsHide specifications
Configuration
DH550/i3800. Screw and barrel not installed — buyer specifies plasticising assembly.
Clamping unit
- Clamping force
- 5500 kN
- Clamping stroke
- 1700 mm
- Tie bar spacing
- 915×915
- Max mold height
- 1000 mm
- Min mold height
- 400 mm
- Platen dimensions
- 1335×1335
Injection unit
- Screw code
- A
Other
DH550/i3800
DH
·S/N: H1055-0008
DH550/i3800 specialised for PP high-plasticisation work — Inovance servo drive and KEBA 2880-0220 controller.
Show full specificationsHide specifications
Configuration
DH550/i3800 + Servo (Inovance) + GB standard + KEBA 2880-0220 + PP high-plasticisation specialised screw.
Clamping unit
- Clamping force
- 5500 kN
- Clamping stroke
- 1700 mm
- Tie bar spacing
- 915×915
- Max mold height
- 1000 mm
- Min mold height
- 400 mm
- Platen dimensions
- 1335×1335
Injection unit
- Screw code
- A
Other
NEO·H500b-e1100c/e840cW
NEO·H
·S/N: H05000001
NEO·H500b heavy-duty machine for optical-grade transparent PC parts. Loaded with 4 core pulls, 8+8 needle valves, water distributors and energy monitoring.
Show full specificationsHide specifications
Configuration
NEO·H500b-e1100c/e840cW with optical-grade transparent PC A-screw, Euro-spec 67 robot interface, electricity meter, increased mold thickness, 4× core pulls, 8× hydraulic needle valves, 8× pneumatic needle valves, 4× water distributors, energy-consumption monitoring, manual core-pull pressure relief, hydraulic core-pull stacking valve, ejector stacking check valve, core-retraction confirmation.
Clamping unit
- Clamping force
- 5000 kN
Injection unit
Other
DH680/i4800
DH
·S/N: H06800006
DHⅡ680/i4800 two-plate machine with Inovance servo and KePlast i2980-0120-00 controller. Standard build.
Show full specificationsHide specifications
Configuration
DHⅡ680/i4800 + Servo (Inovance) + GB standard + KePlast i2980-0120-00 controller. TED-TPL two-plate machine, standard type.
Clamping unit
- Clamping force
- 6800 kN
Injection unit
Other
DH680/i4800
DH
·S/N: H06800008
DHⅡ680/i4800 with secondary clamping, redesigned tie bars and an electroplated A-screw for transparent PC.
Show full specificationsHide specifications
Configuration
DHⅡ680/i4800 with program-added secondary clamping function, new tie-bar structure, PC screw structure, transparent-PC electroplated A-screw.
Clamping unit
- Clamping force
- 6800 kN
Injection unit
Other
DH680/i4800
DH
·S/N: H06800007
DHⅡ680/i4800 standard build — Inovance servo drive and KePlast 2980-0120 controller.
Show full specificationsHide specifications
Configuration
DHⅡ680/i4800 + Servo (Inovance) + GB standard + KePlast 2980-0120 controller. Standard model.
Clamping unit
- Clamping force
- 6800 kN
Injection unit
Other
DH680/i4800
DH
·S/N: H2068-0002
DHⅡ680/i4800 classic-spec build with KEBA CP053, vertical proportional valves and submerged clamping cylinders.
Show full specificationsHide specifications
Configuration
DHⅡ680/i4800 classic model with KEBA CP053 computer. Proportional valves mounted vertically; analogue mold-adjustment and mold-open/close linear-encoder signals. Cost-reduced hydraulic clamping valve plate. Redesigned hydraulic and electrical systems. Submerged clamping cylinders per latest second-generation two-plate clamping solution.
Clamping unit
- Clamping force
- 6800 kN
Injection unit
Other
DT60/i150
DT
·S/N: T3008-0226
Compact DT60/i150 with nitrided plasticising assembly and Techmation control. CE and EUROMAP 67 included.
Show full specificationsHide specifications
Configuration
Standard DT60/i150. CE, EUROMAP 67, nitrided screw & barrel. Techmation controller.
Clamping unit
- Clamping force
- 600 kN
- Clamping stroke
- 330 mm
- Tie bar spacing
- 320×320
- Max mold height
- 330 mm
- Min mold height
- 120 mm
- Ejector stroke
- 80 mm
- Ejector force
- 28 kN
- Ejector pins
- 5
- Max daylight
- 660 mm
- Min mold dimension
- 224×224
Injection unit
- Screw code
- B
- Screw diameter
- 28 mm
- L/D ratio
- 20
- Shot size
- 78 cm³
- Injection weight (PS)
- 71 g
- Injection pressure
- 196 MPa
- Injection rate
- 67 g/s
- Screw speed
- 217 rpm
- Max injection speed
- 119 mm/s
- Injection stroke
- 126 mm
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 11 kW
- Heater power
- 4.5 kW
- Hopper capacity
- 25 kg
NEO·T90-i380
NEO·T
·S/N: T00906010
NEO·T90-i380 with Inovance servo, KEBA control and EUROMAP 67 robot interface. Standard build.
Show full specificationsHide specifications
Configuration
Standard NEO·T90-i380 with Inovance servo, CE, KEBA controller, EUROMAP 67 robot interface, standard screw & barrel.
Clamping unit
- Clamping force
- 900 kN
- Clamping stroke
- 340 mm
- Tie bar spacing
- 360×360
- Max mold height
- 390 mm
- Min mold height
- 150 mm
- Ejector stroke
- 120 mm
- Ejector force
- 34.4 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 252×252
Injection unit
- Screw code
- A
- Screw diameter
- 35 mm
- L/D ratio
- 21.7
- Shot size
- 121 cm³
- Injection weight (PS)
- 110 g
- Injection pressure
- 227.9 MPa
- Injection rate
- 104 g/s
- Screw speed
- 250 rpm
- Max injection speed
- 121 mm/s
- Injection stroke
- 175 mm
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 16 kW
- Heater power
- 6.6 kW
- Hopper capacity
- 25 kg
DT100/i380
DT
·S/N: T01000787
DT100/i380 with nano-IR heating, nickel bimetallic B-screw and dual hydraulic core pulls. KEBA control with EUROMAP 13/67 interfaces.
Show full specificationsHide specifications
Configuration
Standard DT100/i380 with nickel-based bimetallic B-screw, nano-infrared internal & external heating, 2 sets of moving-platen hydraulic cores, additional 1 air-blow valve, EUROMAP 13 + EUROMAP 67 robot interfaces, 6 fixed-platen Shini glass-tube water regulators, KEBA controller.
Clamping unit
- Clamping force
- 1000 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 360×360
- Max mold height
- 380 mm
- Min mold height
- 150 mm
- Ejector stroke
- 120 mm
- Ejector force
- 34 kN
- Ejector pins
- 5
- Max daylight
- 740 mm
- Min mold dimension
- 252×252
Injection unit
- Screw code
- B
- Screw diameter
- 38 mm
- L/D ratio
- 20
- Shot size
- 198 cm³
- Injection weight (PS)
- 181 g
- Injection pressure
- 193 MPa
- Injection rate
- 102 g/s
- Screw speed
- 240 rpm
- Max injection speed
- 99 mm/s
- Injection stroke
- 175 mm
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 11 kW
- Heater power
- 7.68 kW
- Hopper capacity
- 25 kg
DT130/i380
DT
·S/N: T3013-1033
DT130/i380 with Inovance servo, Techmation controller and EUROMAP 67 robot interface. Standard B-screw.
Show full specificationsHide specifications
Configuration
Standard DT130/i380 with Inovance servo, CE, Techmation controller, EUROMAP 67 robot interface, B-screw.
Clamping unit
- Clamping force
- 1300 kN
- Clamping stroke
- 430 mm
- Tie bar spacing
- 420×420
- Max mold height
- 460 mm
- Min mold height
- 160 mm
- Ejector stroke
- 120 mm
- Ejector force
- 34 kN
- Ejector pins
- 5
- Max daylight
- 890 mm
- Min mold dimension
- 294×294
Injection unit
- Screw code
- B
- Screw diameter
- 38 mm
- L/D ratio
- 20
- Injection pressure
- 356 MPa
- Screw speed
- 326 rpm
- Max injection speed
- 99 mm/s
- Injection stroke
- 175 mm
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 11 kW
- Heater power
- 6.6 kW
- Hopper capacity
- 25 kg
DT130/i600
DT
·S/N: T01301876
DT130/i600 with metal A-screw, 3-gear hydraulic motor and dual core pulls. Techmation control.
Show full specificationsHide specifications
Configuration
Standard DT130/i600 with metal A-screw, CE, EUROMAP 67, hydraulic motor with 3 added gears, 2× core puller, Techmation controller.
Clamping unit
- Clamping force
- 1300 kN
- Clamping stroke
- 430 mm
- Tie bar spacing
- 420×420
- Max mold height
- 460 mm
- Min mold height
- 160 mm
- Ejector stroke
- 120 mm
- Ejector force
- 34 kN
- Ejector pins
- 5
- Max daylight
- 890 mm
- Min mold dimension
- 294×294
Injection unit
- Screw code
- A
- Screw diameter
- 42 mm
- L/D ratio
- 21.4
- Shot size
- 287 cm³
- Injection weight (PS)
- 261 g
- Injection pressure
- 213 MPa
- Injection rate
- 142 g/s
- Screw speed
- 170 rpm
- Max injection speed
- 113 mm/s
- Injection stroke
- 207 mm
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 20 kW
- Heater power
- 10 kW
- Hopper capacity
- 50 kg
DT200/i850
DT
·S/N: T02002261
DT200/i850 high-power-servo build with KEBA 12" control, oil-temperature water control and full safety package (Rexroth solenoid detection, oil-level detection, safety relay). Painted RAL7024.
Show full specificationsHide specifications
Configuration
Standard DT200/i850 with high-power servo (Inovance), CE, oil-temperature cooling water control, KEBA 12" controller, 2 sets of moving-platen hydraulic cores + 1 air-blow valve, EUROMAP 13 + EUROMAP 67, 6× Shini glass-tube water regulators on fixed platen, standard B-screw, self-sealing suction filter, Rexroth solenoid-valve power-on detection, oil-level detection, electronic scale control, safety relay, special machine colour (RAL7024), 380V/50Hz.
Clamping unit
- Clamping force
- 2000 kN
- Clamping stroke
- 540 mm
- Tie bar spacing
- 530×530
- Max mold height
- 560 mm
- Min mold height
- 220 mm
- Ejector stroke
- 150 mm
- Ejector force
- 67 kN
- Ejector pins
- 9
- Max daylight
- 1100 mm
- Min mold dimension
- 371×371
Injection unit
- Screw code
- A
- Screw diameter
- 45 mm
- L/D ratio
- 22.2
- Shot size
- 358 cm³
- Injection weight (PS)
- 326 g
- Injection pressure
- 238 MPa
- Injection rate
- 159 g/s
- Screw speed
- 198 rpm
- Max injection speed
- 110 mm/s
- Injection stroke
- 225 mm
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 25 kW
- Heater power
- 16 kW
- Hopper capacity
- 50 kg
DT200/i850
DT
·S/N: T02001454
DT200/i850 with electric pre-plasticisation, Inovance servo, metal screw and KEBA 12" control.
Show full specificationsHide specifications
Configuration
Standard DT200/i850 with electric pre-plasticisation, CE, EUROMAP 67, Inovance servo, KEBA 12" controller, metal screw.
Clamping unit
- Clamping force
- 2000 kN
- Clamping stroke
- 540 mm
- Tie bar spacing
- 530×530
- Max mold height
- 560 mm
- Min mold height
- 220 mm
- Ejector stroke
- 150 mm
- Ejector force
- 67 kN
- Ejector pins
- 9
- Max daylight
- 1100 mm
- Min mold dimension
- 371×371
Injection unit
- Screw code
- A
- Screw diameter
- 45 mm
- L/D ratio
- 22.2
- Shot size
- 358 cm³
- Injection weight (PS)
- 326 g
- Injection pressure
- 238 MPa
- Injection rate
- 159 g/s
- Screw speed
- 198 rpm
- Max injection speed
- 110 mm/s
- Injection stroke
- 225 mm
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 25 kW
- Heater power
- 16 kW
- Hopper capacity
- 50 kg
DT250/i1100
DT
·S/N: T02501521
DT250/i1100 with electric pre-plasticisation, Inovance servo, bimetallic screw and KEBA 12" control.
Show full specificationsHide specifications
Configuration
Standard DT250/i1100 with electric pre-plasticisation, CE, EUROMAP 67, Inovance servo, KEBA 12" controller, bimetallic screw.
Clamping unit
- Clamping force
- 2500 kN
- Clamping stroke
- 550 mm
- Tie bar spacing
- 580×580
- Max mold height
- 600 mm
- Min mold height
- 250 mm
- Ejector stroke
- 160 mm
- Ejector force
- 67 kN
- Ejector pins
- 13
- Max daylight
- 1150 mm
- Min mold dimension
- 406×406
Injection unit
- Screw code
- B
- Screw diameter
- 55 mm
- L/D ratio
- 20
- Shot size
- 601 cm³
- Injection weight (PS)
- 547 g
- Injection pressure
- 185 MPa
- Injection rate
- 205 g/s
- Screw speed
- 250 rpm
- Max injection speed
- 95 mm/s
- Injection stroke
- 253 mm
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 25 kW
- Heater power
- 20 kW
- Hopper capacity
- 50 kg
DT450/i3200
DT
·S/N: T04500192
DT450/i3200 with Inovance servo, KEBA control and nitrided plasticising assembly. EUROMAP 67 ready.
Show full specificationsHide specifications
Configuration
Standard DT450/i3200 with Inovance servo, CE, EUROMAP 67, KEBA controller, nitrided screw & barrel.
Clamping unit
- Clamping force
- 4500 kN
- Clamping stroke
- 800 mm
- Tie bar spacing
- 780×780
- Max mold height
- 780 mm
- Min mold height
- 300 mm
- Ejector stroke
- 200 mm
- Ejector force
- 124 kN
- Ejector pins
- 13
- Max daylight
- 1580 mm
- Min mold dimension
- 546×546
Injection unit
- Screw code
- B
- Screw diameter
- 75 mm
- L/D ratio
- 20
- Shot size
- 1118 cm³
- Injection weight (PS)
- 1017 g
- Injection pressure
- 185 MPa
- Injection rate
- 382 g/s
- Screw speed
- 250 rpm
- Max injection speed
- 95 mm/s
- Injection stroke
- 253 mm
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 51 kW
- Heater power
- 39 kW
- Hopper capacity
- 50 kg
NEO·E110-e160h
NEO·E
·S/N: E01100069
NEO·E110-e160h with hardened A-screw set for optical-grade transparent PC. KEBA 12" touch control.
Show full specificationsHide specifications
Configuration
NEO·E110-e160h with optional fully-hardened A-screw and barrel for optical-grade transparent PC. KEBA 12" touch (code 054).
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 25 mm
- L/D ratio
- 22.4
- Shot size
- 59 cm³
- Injection weight (PS)
- 54 g
- Injection pressure
- 276 MPa
- Holding pressure
- 221 MPa
- Injection rate
- 179 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 120 mm
- Nozzle contact force
- 21.5 kN
Other
- Total electric power
- 27 kW
- Heater power
- 6.3 kW
- Hopper capacity
- 25 kg
- Total weight
- 5 t
- Machine dimensions
- 5×1.5×2.2 m
DE258/E840C
DE
·S/N: E02580024
DE258/E840C ready for buyer-specified plasticising assembly. KEBA 12" touch control.
Show full specificationsHide specifications
Configuration
DE258/E840C. Screw & barrel not installed. KEBA 12" touch (code 054).
Clamping unit
- Clamping force
- 2580 kN
- Clamping stroke
- 500 mm
- Tie bar spacing
- 600×550
- Max mold height
- 600 mm
- Min mold height
- 250 mm
- Ejector stroke
- 140 mm
- Ejector force
- 68 kN
- Ejector pins
- 9
- Max daylight
- 1200 mm
- Min mold dimension
- 420×385
- Platen dimensions
- 920×870
Injection unit
- Screw code
- B
- Screw diameter
- 50 mm
- L/D ratio
- 20
- Shot size
- 422 cm³
- Injection weight (PS)
- 384 g
- Injection pressure
- 200 MPa
- Holding pressure
- 160 MPa
- Injection rate
- 286 g/s
- Screw speed
- 300 rpm
- Max injection speed
- 160 mm/s
- Injection stroke
- 215 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 9 kW
- Total electric power
- 61 kW
- Heater power
- 18.7 kW
- Hopper capacity
- 50 kg
- Oil capacity
- 80 L
- Total weight
- 11.9 t
- Machine dimensions
- 6.7×1.7×2.4 m
DE258/E840C
DE
·S/N: E02580025
DE258/E840C ready for buyer-specified plasticising assembly. KEBA 12" touch control.
Show full specificationsHide specifications
Configuration
DE258/E840C. Screw & barrel not installed. KEBA 12" touch (code 054).
Clamping unit
- Clamping force
- 2580 kN
- Clamping stroke
- 500 mm
- Tie bar spacing
- 600×550
- Max mold height
- 600 mm
- Min mold height
- 250 mm
- Ejector stroke
- 140 mm
- Ejector force
- 68 kN
- Ejector pins
- 9
- Max daylight
- 1200 mm
- Min mold dimension
- 420×385
- Platen dimensions
- 920×870
Injection unit
- Screw code
- B
- Screw diameter
- 50 mm
- L/D ratio
- 20
- Shot size
- 422 cm³
- Injection weight (PS)
- 384 g
- Injection pressure
- 200 MPa
- Holding pressure
- 160 MPa
- Injection rate
- 286 g/s
- Screw speed
- 300 rpm
- Max injection speed
- 160 mm/s
- Injection stroke
- 215 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 9 kW
- Total electric power
- 61 kW
- Heater power
- 18.7 kW
- Hopper capacity
- 50 kg
- Oil capacity
- 80 L
- Total weight
- 11.9 t
- Machine dimensions
- 6.7×1.7×2.4 m
DB325/E1100F
DB (Hybrid)
·S/N: E3033-0001
DB325/E1100F hybrid high-speed machine purpose-built for meal-box production. Loaded with 12×12 water manifolds, 16 air blows and a water-cooled injection screw. Returned from Zhejiang Ruite to our stock.
Show full specificationsHide specifications
Configuration
Dream DB-series hybrid high-speed meal-box machine DB325/E1100F. 2 sets of 12×12 water manifolds with 10 mm quick connectors. 16 air-blow sets with 8 mm quick connectors. Injection screw with temperature detection & water-cooling device; cooling-water inlet controlled by solenoid water valve. Added mold-opening/clamping proportional valve. Originally returned from Zhejiang Ruite to our factory stock. KEBA 12" touch (code 052).
Clamping unit
- Clamping force
- 3250 kN
- Clamping stroke
- 550 mm
- Tie bar spacing
- 620×570
- Max mold height
- 650 mm
- Min mold height
- 250 mm
- Ejector stroke
- 100 mm
- Ejector force
- 67 kN
- Ejector pins
- 13
- Max daylight
- 1200 mm
- Min mold dimension
- 500×460
- Platen dimensions
- 980×930
Injection unit
- Screw code
- A
- Screw diameter
- 55 mm
- L/D ratio
- 27
- Shot size
- 570 cm³
- Injection weight (PS)
- 416 g
- Injection pressure
- 185 MPa
- Holding pressure
- 148 MPa
- Injection rate
- 867 g/s
- Screw speed
- 350 rpm
- Max injection speed
- 500 mm/s
- Injection stroke
- 240 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 43 kW
- Total electric power
- 136 kW
- Heater power
- 27.5 kW
- Hopper capacity
- 50 kg
- Oil capacity
- 420 L
- Total weight
- 15.5 t
- Machine dimensions
- 8.1×2.0×2.0 m
DE328/E840C
DE
·S/N: E03280009
DE328/E840C CE with 50 mm screw, two air-valve sets and an 8-in/8-out water manifold. KEBA 12" touch control.
Show full specificationsHide specifications
Configuration
DE328/E840C CE. Screw diameter 50 mm, 2 air-valve sets, 1 8-in/8-out quick-connect water manifold, plasticising unit 30101000001E3-840 (from our factory stock). KEBA 12" touch (code 052).
Clamping unit
- Clamping force
- 3280 kN
- Clamping stroke
- 580 mm
- Tie bar spacing
- 700×650
- Max mold height
- 700 mm
- Min mold height
- 280 mm
- Ejector stroke
- 150 mm
- Ejector force
- 134 kN
- Ejector pins
- 13
- Max daylight
- 1280 mm
- Min mold dimension
- 490×455
- Platen dimensions
- 1050×1000
Injection unit
- Screw code
- B
- Screw diameter
- 50 mm
- L/D ratio
- 20
- Shot size
- 422 cm³
- Injection weight (PS)
- 384 g
- Injection pressure
- 200 MPa
- Holding pressure
- 160 MPa
- Injection rate
- 286 g/s
- Screw speed
- 300 rpm
- Max injection speed
- 160 mm/s
- Injection stroke
- 215 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 13 kW
- Total electric power
- 61 kW
- Heater power
- 18.7 kW
- Hopper capacity
- 50 kg
- Oil capacity
- 100 L
- Total weight
- 15 t
- Machine dimensions
- 7.2×1.9×2.4 m
DE360/E1400
DE (Full Electric)
·S/N: E3036-0005
DE360/E1400 full-electric machine returned from a Shenzhen Baishengda order to our stock. Standard build with KEBA 12" touch.
Show full specificationsHide specifications
Configuration
Full-electric DE360/E1400. Originally returned from a Shenzhen Baishengda order to our factory stock. Standard machine. KEBA 12" touch (code 054).
Clamping unit
- Clamping force
- 3600 kN
- Clamping stroke
- 710 mm
- Tie bar spacing
- 820×820
- Max mold height
- 720 mm
- Min mold height
- 250 mm
- Ejector stroke
- 160 mm
- Ejector force
- 58.8 kN
- Ejector pins
- 17
- Max daylight
- 1430 mm
- Min mold dimension
- 575×575
- Platen dimensions
- 1160×1160
Injection unit
- Screw code
- B
- Screw diameter
- 60 mm
- L/D ratio
- 20
- Shot size
- 735 cm³
- Injection weight (PS)
- 669 g
- Injection pressure
- 185 MPa
- Holding pressure
- 148 MPa
- Injection rate
- 772 g/s
- Screw speed
- 350 rpm
- Max injection speed
- 300 mm/s
- Injection stroke
- 260 mm
- Nozzle contact force
- 49 kN
Other
- Total electric power
- 104 kW
- Heater power
- 24 kW
- Hopper capacity
- 50 kg
- Total weight
- 22 t
- Machine dimensions
- 7.9×2×2.4 m
DE360/E1400
DE (Full Electric)
·S/N: E3036-0003
DE360/E1400 full-electric machine returned from a Shenzhen Baishengda order to our stock. Standard build with KEBA 12" touch.
Show full specificationsHide specifications
Configuration
Full-electric DE360/E1400. Originally returned from a Shenzhen Baishengda order to our factory stock. Standard machine. KEBA 12" touch (code 054).
Clamping unit
- Clamping force
- 3600 kN
- Clamping stroke
- 710 mm
- Tie bar spacing
- 820×820
- Max mold height
- 720 mm
- Min mold height
- 250 mm
- Ejector stroke
- 160 mm
- Ejector force
- 58.8 kN
- Ejector pins
- 17
- Max daylight
- 1430 mm
- Min mold dimension
- 575×575
- Platen dimensions
- 1160×1160
Injection unit
- Screw code
- B
- Screw diameter
- 60 mm
- L/D ratio
- 20
- Shot size
- 735 cm³
- Injection weight (PS)
- 669 g
- Injection pressure
- 185 MPa
- Holding pressure
- 148 MPa
- Injection rate
- 772 g/s
- Screw speed
- 350 rpm
- Max injection speed
- 300 mm/s
- Injection stroke
- 260 mm
- Nozzle contact force
- 49 kN
Other
- Total electric power
- 104 kW
- Heater power
- 24 kW
- Hopper capacity
- 50 kg
- Total weight
- 22 t
- Machine dimensions
- 7.9×2×2.4 m
DE388/E1100C
DE
·S/N: E03880002
DE388/E1100C with 55 mm screw and the 30101000001E3-1100 plasticising unit. KEBA 12" touch control.
Show full specificationsHide specifications
Configuration
DE388/E1100C with screw diameter 55 mm, plasticising unit 30101000001E3-1100. KEBA 12" touch (code 054).
Clamping unit
- Clamping force
- 3880 kN
- Clamping stroke
- 650 mm
- Tie bar spacing
- 750×700
- Max mold height
- 750 mm
- Min mold height
- 280 mm
- Ejector stroke
- 160 mm
- Ejector force
- 134 kN
- Ejector pins
- 13
- Max daylight
- 1400 mm
- Min mold dimension
- 525×490
- Platen dimensions
- 1100×1060
Injection unit
- Screw diameter
- 55 mm
- L/D ratio
- 20
- Shot size
- 570 cm³
- Injection weight (PS)
- 519 g
- Injection pressure
- 185 MPa
- Holding pressure
- 148 MPa
- Injection rate
- 346 g/s
- Screw speed
- 350 rpm
- Max injection speed
- 160 mm/s
- Injection stroke
- 240 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 13 kW
- Total electric power
- 62 kW
- Heater power
- 20.4 kW
- Hopper capacity
- 50 kg
- Oil capacity
- 100 L
- Total weight
- 17.3 t
- Machine dimensions
- 7.8×2.0×2.3 m
DE388/E1400C
DE
·S/N: E03880006
DE388/E1400C with 1 core pull, 2 air-blow valves and 2 pneumatic needle valves. KEBA 12" touch control.
Show full specificationsHide specifications
Configuration
DE388/E1400C returned to our South China warehouse. Machine No. E03880006. 1× core pull, 2× air-blow, 2× pneumatic needle valve. KEBA 12" touch (code 054).
Clamping unit
- Clamping force
- 3880 kN
- Clamping stroke
- 650 mm
- Tie bar spacing
- 750×700
- Max mold height
- 750 mm
- Min mold height
- 280 mm
- Ejector stroke
- 160 mm
- Ejector force
- 134 kN
- Ejector pins
- 13
- Max daylight
- 1400 mm
- Min mold dimension
- 525×490
- Platen dimensions
- 1100×1060
Injection unit
- Screw diameter
- 60 mm
- L/D ratio
- 20
- Shot size
- 735 cm³
- Injection weight (PS)
- 669 g
- Injection pressure
- 185 MPa
- Holding pressure
- 148 MPa
- Injection rate
- 412 g/s
- Screw speed
- 350 rpm
- Max injection speed
- 160 mm/s
- Injection stroke
- 260 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 13 kW
- Total electric power
- 74 kW
- Heater power
- 24 kW
- Hopper capacity
- 50 kg
- Oil capacity
- 100 L
- Total weight
- 17.5 t
- Machine dimensions
- 7.8×2.0×2.3 m
NEO·E478c-e1400
NEO·E
·S/N: E04780114
NEO·E478c-e1400 top-spec build: auto mold-thickness, EUROMAP 67, 4-zone hot runner, twin-alloy screw, bimetallic barrel and KEBA 15" touchscreen.
Show full specificationsHide specifications
Configuration
NEO·E478c-e1400 fully optioned: A-screw 55 mm, one-touch automatic mold-thickness adjustment, high-sensitivity low-pressure mold protection, ejector-return confirmation + interface for mold-ejector-plate return confirmation, 8-in/8-out quick-connect water manifold, 2 air-blow valve sets, 1 hydraulic core pull, hydraulic ejection, stainless-steel hopper, linkage functions (plasticising during mold open / eject), power-failure protection, USB expansion, EUROMAP 67 robot interface, T-slotted platen, built-in 4-zone hot-runner temperature control, special in-mold-coating program, nickel-based twin-alloy screw, iron-based bimetallic barrel, locating-ring diameter 160 mm, KEBA 15" touch (code 054).
Clamping unit
- Clamping force
- 4780 kN
- Clamping stroke
- 710 mm
- Tie bar spacing
- 850×800
- Max mold height
- 800 mm
- Min mold height
- 320 mm
- Ejector stroke
- 180 mm
- Ejector force
- 134 kN
- Ejector pins
- 17
- Max daylight
- 1510 mm
- Min mold dimension
- 595×560
- Platen dimensions
- 1270×1220
Injection unit
- Screw code
- A
- Screw diameter
- 55 mm
- L/D ratio
- 21.8
- Shot size
- 618 cm³
- Injection weight (PS)
- 562 g
- Injection pressure
- 220 MPa
- Holding pressure
- 176 MPa
- Injection rate
- 346 g/s
- Screw speed
- 350 rpm
- Max injection speed
- 160 mm/s
- Injection stroke
- 260 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 16 kW
- Total electric power
- 74 kW
- Heater power
- 24 kW
- Hopper capacity
- 50 kg
- Oil capacity
- 100 L
- Total weight
- 26 t
- Machine dimensions
- 8.0×2.1×2.3 m
DE488/E1400C
DE (Cable-Tie Special)
·S/N: E04880001
DE488/E1400C specialised for cable-tie production. External Weipu sockets for downstream automation, KEBA 12" touch control.
Show full specificationsHide specifications
Configuration
DE488/E1400C cable-tie special machine. 1× external 380V three-phase 32A socket, 1× external 220V single-phase 10A socket (Weipu). KEBA 12" touch (code 054).
Clamping unit
- Clamping force
- 4880 kN
- Clamping stroke
- 500 mm
- Tie bar spacing
- 680×650
- Max mold height
- 550 mm
- Min mold height
- 240 mm
- Ejector stroke
- 100 mm
- Ejector force
- 67 kN
- Ejector pins
- 5
- Max daylight
- 1050 mm
- Min mold dimension
- 476×455
- Platen dimensions
- 1090×1250
Injection unit
- Screw diameter
- 60 mm
- L/D ratio
- 20
- Shot size
- 735 cm³
- Injection weight (PS)
- 705 g
- Injection pressure
- 185 MPa
- Holding pressure
- 148 MPa
- Injection rate
- 771 g/s
- Screw speed
- 350 rpm
- Max injection speed
- 300 mm/s
- Injection stroke
- 260 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 53 kW
- Heater power
- 24 kW
- Hopper capacity
- 50 kg
- Oil capacity
- 150 L
- Total weight
- 18.5 t
- Machine dimensions
- 6.7×2.0×2.3 m
NEO·E1088c-e7300
NEO·E
·S/N: E10880003
NEO·E1088c-e7300 large-tonnage machine — Inovance servo, ABS bimetallic screw, 4 core pulls and 12×12 water manifold. KEBA 15" touch.
Show full specificationsHide specifications
Configuration
NEO·E1088c-e7300 with Inovance servo, Chinese-standard ABS bimetallic screw, 2× moving-mold + 2× fixed-mold core pulls, 2 air-valve sets, 1× 12-in/12-out quick-connect water manifold. KEBA 15" touch (code 054).
Clamping unit
- Clamping force
- 10880 kN
- Clamping stroke
- 1300 mm
- Tie bar spacing
- 1320×1320
- Max mold height
- 1200 mm
- Min mold height
- 500 mm
- Ejector stroke
- 200 mm
- Ejector force
- 240 kN
- Ejector pins
- 21
- Max daylight
- 2500 mm
- Min mold dimension
- 925×925
Injection unit
- Screw diameter
- 100 mm
- L/D ratio
- 22
- Shot size
- 3927 cm³
- Injection weight (PS)
- 3574 g
- Injection pressure
- 185 MPa
- Holding pressure
- 148 MPa
- Injection rate
- 1072 g/s
- Screw speed
- 160 rpm
- Max injection speed
- 150 mm/s
- Injection stroke
- 500 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 51 kW
- Total electric power
- 229 kW
- Heater power
- 69 kW
- Hopper capacity
- 100 kg
- Oil capacity
- 400 L
- Total weight
- 75 t
- Machine dimensions
- 12×3.1×2.8 m
DE230/E620
DE (Full Electric)
·S/N: E3023-0001
Full-electric DE230/E620 with PS high-plasticising screw, KEBA control and EUROMAP 12. Originally a 2016 exhibition unit transferred to our stock.
Show full specificationsHide specifications
Configuration
Dream DE-series full-electric DE230/E620. KEBA controller, PS high-plasticising screw (45 mm diameter, L/D 20:1), EUROMAP 12 robot interface. Servo oil pump (Feishi). 2016 exhibition machine transferred to our factory stock.
Clamping unit
- Clamping force
- 2300 kN
- Clamping stroke
- 550 mm
- Tie bar spacing
- 620×620
- Max mold height
- 600 mm
- Min mold height
- 250 mm
- Ejector stroke
- 140 mm
- Ejector force
- 49 kN
- Ejector pins
- 13
- Max daylight
- 1150 mm
- Min mold dimension
- 435×435
- Platen dimensions
- 920×920
Injection unit
- Screw diameter
- 45 mm
- L/D ratio
- 20
- Shot size
- 310 cm³
- Injection weight (PS)
- 282 g
- Injection pressure
- 200 MPa
- Holding pressure
- 160 MPa
- Injection rate
- 579 g/s
- Screw speed
- 350 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 195 mm
- Nozzle contact force
- 39.2 kN
Other
- Total electric power
- 68 kW
- Heater power
- 14 kW
- Hopper capacity
- 25 kg
- Total weight
- 11.7 t
- Machine dimensions
- 6.4×1.7×2.3 m
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850069
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850070
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850072
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850073
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850075
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850076
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850077
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850078
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850079
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E85-e220h
NEO·E (BYD)
·S/N: E00850080
NEO·E85-e220h built to BYD specification — transparent-optics A-screw, KEBA 15" touch, OPC UA, EUROMAP 2/12/18 and dual 220V/380V socket pack.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for transparent automotive optical parts. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:23. Insulation cotton. 2 sets of 4-in/4-out water regulator (1 moving + 1 fixed). KEBA 15" touchscreen. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V sockets and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 850 kN
- Clamping stroke
- 320 mm
- Tie bar spacing
- 420×360
- Max mold height
- 410 mm
- Min mold height
- 150 mm
- Ejector stroke
- 80 mm
- Ejector force
- 24.5 kN
- Ejector pins
- 5
- Max daylight
- 730 mm
- Min mold dimension
- 295×250
- Platen dimensions
- 610×550
Injection unit
- Screw code
- A
- Screw diameter
- 28 mm
- L/D ratio
- 23
- Shot size
- 83 cm³
- Injection weight (PS)
- 76 g
- Injection pressure
- 261 MPa
- Holding pressure
- 209 MPa
- Injection rate
- 224 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 135 mm
- Nozzle contact force
- 22 kN
Other
- Total electric power
- 38 kW
- Heater power
- 7.9 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100059
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100060
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100061
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100063
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100065
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100066
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100067
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100068
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100072
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100073
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100074
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E110-e360h
NEO·E (BYD)
·S/N: E01100075
NEO·E110-e360h built to BYD specification — automotive-grade screw, KEBA 15" touch, hydraulic core puller, OPC UA, EUROMAP 2/12/18.
Show full specificationsHide specifications
Configuration
BYD customised machine. Screw for automotive components (transparent variant available). EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:21.7. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets (1 moving + 1 fixed). EUROMAP 12, EUROMAP 18, 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1100 kN
- Clamping stroke
- 360 mm
- Tie bar spacing
- 470×420
- Max mold height
- 480 mm
- Min mold height
- 160 mm
- Ejector stroke
- 100 mm
- Ejector force
- 34.3 kN
- Ejector pins
- 5
- Max daylight
- 840 mm
- Min mold dimension
- 330×295
- Platen dimensions
- 710×660
Injection unit
- Screw code
- A
- Screw diameter
- 32 mm
- L/D ratio
- 21.7
- Shot size
- 128 cm³
- Injection weight (PS)
- 117 g
- Injection pressure
- 282 MPa
- Holding pressure
- 226 MPa
- Injection rate
- 293 g/s
- Screw speed
- 400 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 160 mm
- Nozzle contact force
- 29 kN
Other
- Total electric power
- 41 kW
- Heater power
- 10.6 kW
- Hopper capacity
- 25 kg
NEO·E168c-e500h
NEO·E (BYD)
·S/N: E01680061
NEO·E168c-e500h built to BYD specification with EUROMAP 67 robot interface and 8-zone hot-runner control — full automation-ready package.
Show full specificationsHide specifications
Configuration
BYD customised machine. EUROMAP-2 platen with T-slots. Inovance motor/drive. L/D ratio 1:22.1. Insulation cotton. Water regulator 6-in/6-out on fixed platen + 4-in/4-out on moving platen. KEBA 15" touchscreen. 1 core puller. 2 air-blast sets. 1 pneumatic sequence valve interface. EUROMAP 12, EUROMAP 18, EUROMAP 67 robot interface. 8-zone hot-runner control. 3 I/O point sets, OPC UA interface. Additional 3×220V and 4×380V/32A sockets.
Clamping unit
- Clamping force
- 1680 kN
- Clamping stroke
- 400 mm
- Tie bar spacing
- 520×460
- Max mold height
- 530 mm
- Min mold height
- 150 mm
- Ejector stroke
- 120 mm
- Ejector force
- 56 kN
- Ejector pins
- 5
- Max daylight
- 930 mm
- Min mold dimension
- 365×320
- Platen dimensions
- 770×720
Injection unit
- Screw code
- A
- Screw diameter
- 38 mm
- L/D ratio
- 22.1
- Shot size
- 204 cm³
- Injection weight (PS)
- 186 g
- Injection pressure
- 244 MPa
- Holding pressure
- 200 MPa
- Injection rate
- 413 g/s
- Screw speed
- 350 rpm
- Max injection speed
- 400 mm/s
- Injection stroke
- 180 mm
- Nozzle contact force
- 82 kN
Other
- Max pump pressure
- 17.5 MPa
- Pump motor power
- 11 kW
- Total electric power
- 67 kW
- Heater power
- 13 kW
- Hopper capacity
- 25 kg
- Oil capacity
- 80 L
About our clearance offer
TEDESolutions offers a clearance sale of Tederic injection molding machines including new, demo and used units from the NEO·T, DT, DE, NEO·E, NEO·H series and BYD-customised variants. Clamping forces from 600 to 33,000 kN, KEBA and Techmation controllers, EUROMAP 12/13/18/67, OPC UA, hardened PC screws, water-cooled plasticising assemblies and hybrid / full-electric packages. All machines are covered by warranty and service support from our Krakow base.
- Stock on hand: 54 injection molding machines ready for shipment from the Tederic warehouse.
- Clamping-force range: 600 kN – 33,000 kN (from the compact DT60/i150 to two-platen NEO·H).
- Control: KEBA (CP053, 2880, 2980, KePlast i2980, 12" / 15" touchscreen) and Techmation.
- Standards: CE, EUROMAP 67, 27-month warranty and full promotion package included.
- Krakow office: +48 507 161 780, service +48 666 457 822.
Frequently asked questions
What injection molding machines are available in the clearance sale?
Do clearance machines come with a warranty?
How do I get pricing for a clearance machine?
What are the delivery terms for clearance machines?
Do you offer financing for clearance machines?
Interested in clearance machines?
Contact us for a detailed offer and pricing on your selected machine.
Contact us →