TEDESolutions
NEO·M Series M1120s - Technical Specifications
December 13, 2025
TEDESolutions sp. z o.o. | ul. Stolarska 6C, 86-021 Maksymilianowo | +48 507 161 780 | biuro@tedesolutions.pl | www.tedesolutions.pl
11,200
kN
2
Variants
49
t
NEO·M Series M1120s Machine Overview
Tederic NEO·M Series M1120s multi-component injection molding machine with a clamping force of 11200 kN (1120 metric tons). This is a smaller capacity machine within the NEO·M Series series.
Mold opening stroke: 2500mm. Tie bar spacing: 1260×1175mm (width × height). Maximum daylight: 4000mm. Mold height range: 650mm to 1250mm.
Overall machine dimensions: 13.7×4×3.4 m (L×W×H). Machine weight: 49 t.
The NEO·M Series series includes 10 models with clamping forces from 11200 kN to 28200 kN (1120-2820 metric tons). A total of 34 injection unit configurations are available in this series.
Ideal for automotive interiors, consumer electronics housings, and multi-material technical parts.
Clamping Unit: M1120s
Clamping Force
11,200 kN
Mold Opening Stroke
2,500 mm
Max Mold Height
1,250 mm
Min Mold Height
650 mm
Tie Bar Spacing
1260 × 1175 mm
Platen Dimensions (W×H)
1815 × 1730 mm
Min. Mold Dimensions
882 × 822 mm
Max Daylight
4,000 mm
Middle Platen Dimensions (W×H)
1600 × 1400 mm
Middle Plate Thickness
200 mm
Max Daylight (Middle Platen)
1,900 mm
Rotation Table Weight
18.0 t
Machine Weight
49.0 t
Overall Dimensions (L×W×H)
13.7 × 4 × 3.4 m
Multi-Component Injection Units
Type 12 injection units
| Parameter | injection unit 1 i3800 | injection unit 2 i1900 |
|---|---|---|
| Screw Diameter | 70 mm | 55 mm |
| Shot Volume | 1,554 cm³ | 710 cm³ |
| Shot Weight (PS) | 1,414 g | 646 g |
| Injection Pressure | 236 MPa | 260 MPa |
| Injection Rate | 620 g/s | 310 g/s |
| Max Injection Speed | 177 mm/s | 143 mm/s |
| Injection Stroke | 404 mm | 299 mm |
| Screw Speed | 165 rpm | 210 rpm |
| Heater Power | 46 kW | 24 kW |
| Hopper Capacity | 50 kg | 50 kg |
| Oil Tank Volume | 1,300 L | 700 L |
Type 22 injection units
| Parameter | injection unit 1 i3800 | injection unit 2 e1400h |
|---|---|---|
| Screw Diameter | 70 mm | 50 mm |
| Shot Volume | 1,554 cm³ | 510 cm³ |
| Shot Weight (PS) | 1,414 g | 464 g |
| Injection Pressure | 236 MPa | 266 MPa |
| Injection Rate | 620 g/s | 536 g/s |
| Max Injection Speed | 177 mm/s | 300 mm/s |
| Injection Stroke | 404 mm | 260 mm |
| Screw Speed | 165 rpm | 350 rpm |
| Heater Power | 46 kW | 24 kW |
| Hopper Capacity | 50 kg | 50 kg |
| Oil Tank Volume | 2,000 L | 2,000 L |
Variants (2)
Type 1
| Parameter | Variant A | Variant B |
|---|---|---|
| ID | i3800 | i1900 |
| Screw Diameter | 70 mm | 55 mm |
| Shot Volume | 1,554 cm³ | 710 cm³ |
| Shot Weight (PS) | 1,414 g | 646 g |
| Injection Pressure | 236 MPa | 260 MPa |
| Injection Rate | 620 g/s | 310 g/s |
Type 2
| Parameter | Variant A | Variant B |
|---|---|---|
| ID | i3800 | e1400h |
| Screw Diameter | 70 mm | 50 mm |
| Shot Volume | 1,554 cm³ | 510 cm³ |
| Shot Weight (PS) | 1,414 g | 464 g |
| Injection Pressure | 236 MPa | 266 MPa |
| Injection Rate | 620 g/s | 536 g/s |
Equipment & Options
Standard
Optional
—Not Available
Platen with T slots
Standard
Platen with tapped holes
Standard
Platen (according to EUROMAP 2)
Optional
High rigidity 5 points-double toggle structure
Standard
Mechanical safety
Standard
Electrical safety
Standard
Hydraulic safety
Standard
Auto-mold height adjustment function
Standard
Mold open, closing and mold adjusting controlled by transducer
Standard
Fix-quantity type auto central lubrication system
Standard
Mechanical adjust support for moving platen
Standard
High rigidity steel wear strips for moving platen
Standard
Auto safety door
Optional
EUROMAP 18 robot interface
Standard
Widened door and covers
Standard
Safety pressure plate under mold area
Optional
Two water regulation manifolds
Standard
Quick coupling for water regulator
Standard
Two air blow circuits
Standard
Four air blow circuits
Optional
Glass water flow regulators
Optional
Low pressure mold protection
Standard
Standard screw
Standard
Specialized screw and barrel
Optional
Shut off nozzle
Optional
Double cylinder injection
Standard
Double carriage cylinder injection unit
Standard
Carriage transducer
Standard
Screw rotation speed display
Standard
Hydraulic plasticizing
Standard
Electrical plasticizing
Optional
Proportional back pressure control
Standard
Closed-loop control of the temperature at the discharge port
Standard
Barrel insulation cover
Standard
Nozzle cover
Standard
Self-lock valve for carriage
Standard
Material loading platform
Standard
Manual central lubricating device for carriage
Standard
Carriage central auto lubrication device
Optional
Ceramic heating band
Standard
Screw mobile feed hopper
Standard
Gas-assisted injection interface
Optional
Hopper dryer
Optional
Stainless hopper
Standard
Barrel insulation device
Optional
Equipment & Options
Standard
Optional
—Not Available
Clamping Unit(22)
Platen with T slots
Standard
Platen with tapped holes
Standard
Platen (according to EUROMAP 2)
Optional
High rigidity 5 points-double toggle structure
Standard
Mechanical safety
Standard
Electrical safety
Standard
Hydraulic safety
Standard
Auto-mold height adjustment function
Standard
Mold open, closing and mold adjusting controlled by transducer
Standard
Fix-quantity type auto central lubrication system
Standard
Mechanical adjust support for moving platen
Standard
High rigidity steel wear strips for moving platen
Standard
Auto safety door
Optional
EUROMAP 18 robot interface
Standard
Widened door and covers
Standard
Safety pressure plate under mold area
Optional
Two water regulation manifolds
Standard
Quick coupling for water regulator
Standard
Two air blow circuits
Standard
Four air blow circuits
Optional
Glass water flow regulators
Optional
Low pressure mold protection
Standard
Injection Unit(23)
Standard screw
Standard
Specialized screw and barrel
Optional
Shut off nozzle
Optional
Double cylinder injection
Standard
Double carriage cylinder injection unit
Standard
Carriage transducer
Standard
Screw rotation speed display
Standard
Hydraulic plasticizing
Standard
Electrical plasticizing
Optional
Proportional back pressure control
Standard
Closed-loop control of the temperature at the discharge port
Standard
Barrel insulation cover
Standard
Nozzle cover
Standard
Self-lock valve for carriage
Standard
Material loading platform
Standard
Manual central lubricating device for carriage
Standard
Carriage central auto lubrication device
Optional
Ceramic heating band
Standard
Screw mobile feed hopper
Standard
Gas-assisted injection interface
Optional
Hopper dryer
Optional
Stainless hopper
Standard
Barrel insulation device
Optional
Electrical System(31)
KEBA controller
Standard
KEBA 15-inch touch screen
Standard
Memory with 200 sets of mold parameters
Standard
All action instant monitoring
Standard
Production monitoring
Standard
Failure alarm display
Standard
Changeover from injection fill to hold by injection pressure
Optional
I/O monitoring display
Standard
3 color light (with buzzer)
Standard
Motor overload protection
Standard
Front/back door emergency stop switch
Standard
5 pins socket of 380V/32A, 2 groups
Standard
5 pins socket of 380V/16A, 1 group
Standard
3 pins socket of 230V/16A, 1 group
Standard
Transformer for servomotor system
Optional
EUROMAP 13 neutron connection
Standard
EUROMAP 12 robot interface
Standard
EUROMAP 67 robot interface
Optional
Double protection for heating
Standard
Safety relay monitoring
Standard
SSR heating control
Standard
Hot runner control system & interface
Optional
Instant power consumption monitoring
Standard
Instant clamping force monitoring
Standard
230V/10A Industrial plug
Standard
Electrical cabinet lighting device
Standard
Remote control
Optional
Close-loop control for mold open/close
Standard
Safety pedal monitoring
Standard
Open-phase protection
Standard
Inspection of repair door
Standard
Hydraulic System(26)
Fast response servo system
Standard
Increased motor-pump unit
Standard
Independent cooling system
Standard
Independent filtration system
Optional
Pressure control for injection to hold on pressure
Standard
Programmable injection sequence
Optional
Fast injection with accumulator
Standard
Carriage self-lock valve
Standard
Proportional injection valve
Optional
Injection servo valve
Standard
Oil temp. detector
Standard
Oil level alarm
Standard
Anti-explosive chain
Standard
Self-lock suction oil filter
Standard
Control of oil temperature and cold water valve
Standard
Two core pull circuits on moving platen
Standard
Two core pull circuit on moving platen, two core pull circuit on fixed
Optional
Sequence valve
Standard
Fast molding closing device
Standard
Quick clamping device
Standard
Ejector on-the-fly
Standard
Hydraulic safety device
Standard
Plasticize on-the-fly
Optional
Plasticizing & ejector on the fly
Standard
Proportional valve control for clamp open and close
Standard
Servo valve control for clamp open and close
Optional
Other Equipment(14)
Standard tederic color
Standard
Shock-proof pad
Standard
Foundation steel plate, Foundation anchor bolts
Optional
Spare parts, regular tools, mold clamper, extended nozzle, operation manual
Standard
High base
Optional
Robot
Optional
Magnet (for hopper dryer)
Optional
Chiller
Optional
Mould temp controller
Optional
Dehumidifier
Optional
Autoloader
Optional
Fumigated wooden packaging
Optional
With full-tank hydraulic oil
Optional
Products fetching platform
Standard
Similar Machines by Clamping Force
Other Tederic models with clamping force around 11200 kN from different series.
DE-C Series
DE1088
10880 kN(1088t)
All-Electric
9 screw variants
NEO·HII SeriesH1080II
10800 kN(1080t)
Two-Platen
6 screw variants
NEO·HII SeriesH1080II wp
10800 kN(1080t)
Two-Platen
3 screw variants
NEO·EII SeriesE1080II
10800 kN(1080t)
All-Electric
9 screw variants
Compare machines from different series to find the best fit for your needs.
Related Articles
Learn more about injection molding technology and best practices.
Insert Molding & In-Mold Electronics
Advanced techniques for electronics integration and hybrid manufacturing.
Read moreComplete Guide to Injection Molding Machines
Comprehensive overview of machine types, selection criteria, and key specifications.
Read moreInjection Molding Defects: Identification & Solutions
Common defects, their causes, and practical solutions for quality improvement.
Read more